Operating treatments of floating fish feed machine
1. Running treatments of drifting fish feed machine
( 1) Preventative measures before beginning as well as after stopping
① Examine all parts of fish feed floating pellet making maker, specifically the connecting screws and support screws of each area of the puffing chamber, the linking screws between the motor base as well as the frame, and the screw link in between the puffing chamber and also the structure, and there must be no looseness;
② Manually rotate the primary shaft, right now, there need to be no rubbing audio in the fish feed floating pellet making machine puffing tooth cavity;
③ Begin the feeding auger of fish feed drifting pellet making machine, check its stepless high-speed performance, as well as require typical operation;
④ Examine as well as cleanse the water and gas courses prior to starting the fish feed floating pellet making maker, and all filters need to be cleansed;
⑤ Prior to beginning the fish feed floating pellet making machine, inspect whether the circuitry of the electrical control component is right, whether the rotation of each motor is right, as well as whether the control is reliable;
⑥ After the fish feed drifting pellet making maker is stopped, you must wear high-temperature gloves, rapidly eliminate the discharge mold, as well as right away tidy it while it is warm, and also start the main motor to clear the product gathered in the blowing cavity. When the corn is blown, soybean powder should be included The material is rinsed clean;
⑦ Pay attention to safety and security when unloading the machine, and do not stand in front of the machine to prevent threat caused by residual stress in the fish feed drifting pellet making machine cavity;
⑧ After the fish feed drifting pellet making equipment is running generally, it will not be shut down at will.
Related post: fish feed mill plant
( 2) Power on
① Prior to starting the fish feed floating pellet making machine, inspect the fasteners, and there must be no looseness;
② Ensure the typical supply of steam and water;
③ Make certain that the power supply and electrical home appliances are typical;
④ Open up the heavy steam valve, pre-heat the drifting fish pellet equipment blowing chamber, the temperature level is about 100 levels;
⑤ Start the fish feed drifting pellet making maker: begin the conditioner, begin the feeding auger, when there is material draining from the outlet of the conditioner, start adding steam to the conditioner.
A small amount of water is added, and the material is fed into the blowing cavity at the same time. After the product is extruded by fish feed drifting pellet making machine, the puffing effect as well as dampness of the item are readjusted.
Related post: https://www.richipelletmachine.com/fish-feed-mill-plant/
( 3) Downtime
After the fish feed floating pellet making maker manufacturing concerns an end, it requires to be stopped. The quit series is: feeding auger and also conditioner. After that wait until the indicated worth of the primary engine present on the electric control cabinet becomes the no-load existing value, after that quit the primary motor as well as the oil pump electric motor.
( When the corn is blown, concerning 25 kg of soybeans should be fed right into the bypass feeding port of the initial section of the puffing dental caries. To cleanse the recurring corn product in the blowing tooth cavity, and afterwards quit the major motor to avoid the fish feed drifting pellet making equipment from blocking), after that promptly dismantle the blowing cavity of the tail section for cleaning.
After cleaning, use oil to the internal wall of the main shaft as well as screw head (After feeding oil), re-install it as well as wait on the following boot;
When you see that the product degree sign on the silo shows that the product degree has reached the lowest level, begin to prepare for closure. At this time, do not stop the feeding auger and conditioner, as well as quit feeding when the primary fish feed drifting pellet making device present drops to the no-load present auger as well as conditioner.
2. Operation series of floating fish feed machine
( 1 )When blowing soybeans, both areas at the inlet end of the blowing cavity are single screw heads, and the 3 sections at the electrical outlet end are geared up with double screw heads.
Initially, include heavy steam to the jacket to preheat the blowing dental caries to regarding 100 levels, and also placed the screws on the blowing cavity at the tail section. After the plug is tightened, loosen it for 3-4 turns, and afterwards tighten up the screw plug to repair the screw plug prior to feeding.
Related post: poultry feed plant price
By regulating the stepless high-speed system of the feeding auger, the feeding rate is from slow-moving to fast, and the feeding rate is from tiny to big. After the soybean dish is ejected from the screw plug opening, add the cover to get in the typical production, as well as set up the screw connects with different apertures to get soybean dish with various yields as well as excellences.
By setting up the cone-shaped pressure rings of different diameters, the indicated temperature of the four-section (discharge end) puffing dental caries is 130-140 degrees. It is recommended that the screen of the crusher utilized for squashing soybeans need to have a size of 3-4.
( 2 )When extruding powdery feed by fish feed drifting pellet making machine, the extruding screws in the squeezing out dental caries are all single screw heads, add vapor to the jacket to preheat the puffing tooth cavity to about 80 degrees, and also get in the fish feed drifting pellet making machine and steam evenly satiated and also solidified powder.
Concerning 18%, this have to be carried out in the feed conditioner, as well as the feed quantity is controlled by the stepless rate controling mechanism from little to big. Keep in mind that the reading of the ammeter of the primary electric motor should not go beyond the ranked present of the major engine of fish feed drifting pellet making machine. my website
Be careful of overwhelming the electric motor as well as squeezing out powdery products. When the temperature level of the extruding chamber at the discharge end is controlled to an proper degree by setting up conical pressure rings with different diameters.
The above is the concept, structure and operating procedures of the fish feed drifting pellet making machine introduced by Richi Equipment. In quest of crunchy preference and excellent appearance, manufacturers often add a raising agent (or cooking powder), which contains a certain amount of light weight aluminum aspects, and also produces gas when heated during baking or frying, and also the leavening agent is inside the food.
For details please contact: fish feed machine
WhatsApp:86 138 3838 9622
Email:enquiry@richipelletmachine.com
Ingen kommentarer endnu